Rear Side Markers Reflectors Tail Light Precut Smoked Vinyl Tint Fits Kia Stinger GT 2018-2020

Bogar Tech Designs SKU: T-STINGERGT-TLIGHT-DARKSMOKE

$33.99

Shipping calculated at checkout

Same day shipping on orders placed Mon-Fri by 6am Pacific Time

Available Now!

Customer Reviews

Based on 15 reviews
53%
(8)
13%
(2)
27%
(4)
7%
(1)
0%
(0)
M
Marc M louis
Good and easy to install

But these do not fit the 2022 tails lights only the side reflector just to let the 2022 owners know

I
Inna Semenova
Works as promised

Works as promised, installation requires being careful, that's hey why there are two set of two. Few months in adhesion is perfect includingultiple car washes.

W
Wyatt C Smith
Quality products

The product fit properly and was easily installed.

E
Eddie
Gift from side piece...

They went on Ez!. Jus clean all surfaces b4 application.. Great look

D
D G
Great removable option that won't break the bank

These turned out a bit better than I expected. Wanted something I could use to black out this section of the rear lights without permanently painting the lenses, and it definitely does the job.Most of us are probably DIY buyers, so a couple of install tips I picked up on the fly:1) Make sure you apply plenty of water with a spray bottle to both sides of the overlay, as well as the surface of the lenses while you're applying/aligning the pieces. If you don't lay it perfectly the first time, you can lift the overlay back up and respray until you get tue desired alignment.2) Don't be afraid to use your hands. After I minimally scratched the first piece I placed and adhered, I switched from a felt wrap squeegee to a good ole' elbow grease and finger strength to push the remaining bubbles out of the overlay (spraying with water often to keep the surface slick). I did still use the squeegee to push large bubbles out while getting my placement right.3) Use minimal heat. If you have a hair dryer I would almost suggest using it versus a heat gun. Again, trial and error after applying too much heat and too early. You should only need the heat after the overlay is mostly placed. Try to work out as many air bubbles as possible before using a heat source (unless you need to use heat to stretch the vinyl for fitment).4) Patience and attention to detail is key. Upon first glance, I was not satisfied with the look of these. I thought they looked rippled and too bubbly/foggy. The instructions warn of this with the same message: don't fret. I realized within several hours that the overlay began to adhere fully. After 24 hours there were still a couple of small bubbles I wanted to work out, so I re-applied some moisture/heat and got them looking great.Overall would definitely recommend the product for the price and ease of use!

Vehicle: Fits Kia Stinger GT, GT1, and GT2 2018 2019 2020
(Does not fit Base and Premium trims)

The FULL KIT includes
Includes Taillight, Side and Rear Reflector Overlays. Outline of what's included can be seen in the images.

Film: 20% Dark Smoke. 3 mil thick, strong enough to resist the elements and expected to last 5 years +


Value wise, these add a huge visual impact for a very low price. Tint may look darker or lighter depending on lighting.

Installation:
Wet application recommended
Professional Installation Is Recommended For Beginners
Install in a temperature of at least 70°F
Slight tuck in or trim may be necessary depending on your preference
Detailed installation instructions are included in the package


100% satisfaction guaranteed! If you are not satisfied with your order, please feel free to reach out to us. Be sure to check out our other listings for similar great products!

 

Bogar Tech Designs Product Warranty

VEHICLES WITH INSTALLED TINT OVERLAY COVERS MAY NOT BE STREET LEGAL. PLEASE CHECK WITH YOUR LOCAL LAWS AND REGULATIONS CONCERNING THE LEGALITY OF THIS FILM. CUSTOMER USES PRODUCT AT OWN RISK. WE ARE NOT LIABLE FOR ANY DAMAGE OCCURING DURING OR RESULTING FROM THE INSTALLTION OF THE PRODUCT.

Recommended Products